
The C9200L-24P-4G-E is the 24-port PoE+ member of Cisco's Catalyst 9200L line: 24 × 10/100/1000 PoE+ copper downlinks, four fixed 1G SFP uplinks, a 600W AC supply and the Network Essentials licence. It is an access-layer switch for branch and mid-size campus wiring closets where phones, access points and cameras need power, and where a 1G uplink is enough.
Three numbers decide whether this model fits, and all three are routinely assumed rather than checked: the PoE budget, the uplink ratio, and what the -E licence actually leaves out. This guide goes through each one against Cisco's published figures.
| Parameter | C9200L-24P-4G-E |
|---|---|
| Downlink ports | 24 × 10/100/1000 PoE+ (RJ-45) |
| Uplink ports | 4 × 1G SFP, fixed (no network module slot) |
| PoE budget | 370W with the included PWR-C5-600WAC; 740W with a second supply |
| Switching capacity | 56 Gbps (136 Gbps with stacking) |
| Forwarding rate | 41.66 Mpps (101 Mpps with stacking) |
| Stacking | StackWise-80, 80 Gbps, up to 8 members; needs C9200L-STACK-KIT |
| DRAM / flash | 2 GB / 4 GB |
| Default power supply | PWR-C5-600WAC |
| Fans | Fixed, redundant |
| Software | Cisco IOS XE, Network Essentials tier |
| Dimensions (H × W × D) | 4.4 × 44.5 × 28.8 cm (1.73 × 17.5 × 11.3 in), chassis only |
Source: Cisco Catalyst 9200 Series data sheet (bandwidth and PoE tables, forwarding rates measured with 64-byte IPv4 packets). Where the data sheet does not publish a figure, this guide does not state one.
The switch ships with one PWR-C5-600WAC and makes 370W available to PoE ports. Cisco adds a footnote that matters more than the headline: available power is "limited by port number and port rating (for example, 24 PoE+ 30W ports = 720W)". A fully loaded 24-port PoE+ chassis can demand 720W, roughly twice the single-supply budget.
What 370W actually covers, at common device classes:
If your closet will power 24 Wi-Fi 6E access points at class 4, this model is the wrong part, not a marginal one: you need the second supply (740W), or a 48-port model with a 1KW supply. Sizing on "24 ports" alone is how the second order happens.
The downlinks can carry 24 Gbps in each direction; the uplinks carry 4 Gbps. That is 6:1 oversubscription as shipped, and 24:1 if you only populate one uplink. For a closet of phones, cameras and office PCs that is normal and fine. For a closet aggregating Wi-Fi 6 traffic from 24 access points, it is where the network bottlenecks first.
If the design needs 10G uplinks, the matching part is the C9200L-24P-4X: same 24 PoE+ ports and same 370W/740W budget, four fixed 10G SFP+ uplinks, 128 Gbps switching capacity and 95.23 Mpps. It is a different SKU, not an option on this one — the uplinks on the -4G are fixed and cannot be swapped.
The -E suffix is the licence tier, and it changes what the switch can be asked to do. Cisco's feature table splits the two tiers like this:
Two practical consequences. A design that relies on VRRP for gateway redundancy needs the -A part (C9200L-24P-4G-A). A design that needs PVLAN isolation in the closet needs it too. Everything else in a standard access closet — 802.1X, QoS, routed access with OSPF — stays inside Essentials.
Licences cannot be changed by re-flashing a part number after shipment, so the tier has to be decided at order time.
Catalyst 9200L models stack with StackWise-80 at 80 Gbps, up to eight members, using the C9200L-STACK-KIT. Two rules trip people up:
Stacked, the published figures for this model are 136 Gbps switching capacity and 101 Mpps forwarding — the aggregate of the stack, not of one member.
| C9200L-24P-4G-E | C9200L-24P-4X-E | C9200-24P-E | |
|---|---|---|---|
| Downlinks | 24 × PoE+ | 24 × PoE+ | 24 × PoE+ |
| Uplinks | 4 × 1G fixed | 4 × 10G fixed | Modular (network module sold separately) |
| Switching capacity | 56 Gbps | 128 Gbps | 128 Gbps |
| Forwarding rate | 41.66 Mpps | 95.23 Mpps | 95.23 Mpps |
| Stacking | StackWise-80, 80 Gbps | StackWise-80, 80 Gbps | StackWise-160, 160 Gbps |
| PoE budget | 370W / 740W | 370W / 740W | 370W / 740W |
| Fans and PSU | Fixed fans, field-replaceable PSU | Fixed fans, field-replaceable PSU | Field-replaceable fans and PSU |
| Typical fit | Branch closet, phones and cameras | Closet with 10G aggregation | Closet needing uplink flexibility |
The step from -4G to -4X is an uplink decision. The step from 9200L to 9200 is a platform decision: modular uplinks, field-replaceable fans and 160 Gbps stacking.
Every unit we ship is new and factory sealed. The data sheet lists the chassis with its default PWR-C5-600WAC supply; it does not list stacking cables, SFP optics, rack-mount hardware or DNA term licences as included. If the install depends on any of them, confirm them on the order rather than after delivery — a 9200L cannot be upgraded into a -4X, and a -E cannot be licensed into a -A afterwards.
How much PoE does the C9200L-24P-4G-E provide?
370W with the included 600W supply, 740W with a second PWR-C5-600WAC. Cisco notes the budget is also limited by port rating, so 24 ports at 30W would need 720W.
Does it support 10G uplinks?
No. The four uplinks are fixed at 1G. The 10G version of the same switch is the C9200L-24P-4X-E.
Can it stack with a Catalyst 9200 (non-L)?
No. 9200L models stack with 9200L models only, at the same licence level, using StackWise-80 and the C9200L-STACK-KIT.
Is the -E licence upgradeable to Advantage later?
Treat the tier as fixed at order time and decide on the -A part number if VRRP, PVLAN or multicast routing is required.
Is it Layer 3?
Yes, within Essentials scope: static routes, RIP, EIGRP stub and OSPF up to 1,000 routes.
Need the C9200L-24P-4G-E in quantity? Send the quantity and delivery country and we reply with unit price and lead time. Full C9200L-24P-4G-E product page and specifications · Request a quote
Specification sources: Cisco Catalyst 9200 Series data sheet (bandwidth table, PoE table, licensing table); Cisco C9200L-24P-4G-E data sheet (quick spec). Figures quoted as published; no reseller estimates.